CQ ELECTRONICS BLOG · AIRBAG MODULE

Subaru Outback 2022 airbags deployed? We clear the crash data

When the airbags go off, the airbag (SRS) module records the crash and locks itself, and the airbag light stays on. In a 2022 Subaru Outback that crash data is encrypted, so a scan tool can't clear it. We clear it on a test bench at our Brisbane workshop, and you keep your original module.

  • Subaru Outback 2022
  • Airbags deployed
  • Crash data cleared
  • Encrypted module
  • Seventeen Mile Rocks, Brisbane
Airbag (SRS) module from a 2022 Subaru Outback on the CQ Electronics bench: a green circuit board with a large chip and two orange capacitors, thin wires soldered to the board, a black adapter board above it and the module's yellow connector at the bottom
2022Subaru Outback
LockedModule after the airbags fired
EncryptedThe stored crash data
BenchTest-bench methods, your module kept

Short answer: when the airbags of a Subaru Outback deploy, the airbag (SRS) module stores the crash data and locks, and the airbag light stays on. On a newer car such as the 2022 Outback that data is encrypted, so a scan tool or a simple chip read can't clear it. We connect the module to a test bench, use the method that suits that module to clear the crash data, and check the module before it goes back. Your original module is kept. A reset does not replace airbags or seatbelt pretensioners that have fired, or damaged sensors: those still have to be replaced. If the airbag light is on after a crash, contact CQ Electronics for a quote.

01The job: a 2022 Subaru Outback after the airbags deployed

This article follows the airbag module of a 2022 Subaru Outback whose airbags had deployed. The photos were taken at our workshop bench. No customer or vehicle details are shown.

After a deployment, a car usually shows:

  • The airbag (SRS) warning light staying on.
  • A list of airbag fault codes when it is scanned.
  • An airbag system that is not ready for a second impact until the stored crash data is dealt with.

The airbags themselves, the seatbelt pretensioners and any damaged sensors have to be replaced as part of the repair. What is left is the module, which still holds the crash record. The usual choices are a new module, or having the crash data cleared from the original. We do the second.

02What the airbag module does in a crash

The airbag module is the brain of the safety system. It reads the impact sensors, decides which airbags and seatbelt pretensioners to fire, and records what happened. That record is the crash data.

Once the module has stored a deployment, it keeps the airbag light on and does not treat the system as ready until the crash data is cleared or the module is replaced. That is deliberate: a system that has fired shouldn't pretend that it is ready to fire again.

  • ImpactThe sensors detect the crash and the airbags fire.
  • Module recordsThe airbag module stores the crash data.
  • Module locksThe airbag light stays on. The system is not ready.
  • Test benchThe crash data is cleared and the original module is kept.
    We work here
  • Car repairedFired airbags and damaged parts are replaced, and the system is checked.

03Why newer modules are harder

Cars get more electronic every year, and the modules inside them get more complex. Airbag modules are no exception, and it shows in how hard the crash data is to reach.

OlderMany older modules kept the crash record in a small, separate memory chip that a programmer could reach.
NewerNewer modules keep it inside the processor's own memory. The data is encrypted, so it can't simply be read and edited.
This oneThe 2022 Subaru Outback module: encrypted data, cleared on the bench with a method chosen for this module.

A scan tool can't do it. A plain chip read can't do it either. That is why, on the test bench, we use several different methods, and which one works depends on the module. There is no one-click answer, so we check the module first.

04The module on our bench

The photo at the top of this page shows the component side of the module. This is the reverse side.

The reverse side of the airbag module circuit board: a large chip with thin coloured wires soldered to the board beside it, wire sleeves marked RESET, rows of round solder pads and the yellow connector housing below

Reaching a module that doesn't offer an easy way in

  • Fine wires are soldered to the board next to the chip. They lead back to the bench adapter.
  • Labelled sleeves on the wires keep the connections straight. One reads RESET.
  • The solder pads at the bottom are where the connector pins pass through to the car's plug.

The module is on the bench and not in a car, so every connection it needs is made by hand.

The same board-level approach is behind our Ford Ranger and Hyundai ECU repairs.

05The bench setup

Bench setup
The bench setup seen from above: the airbag module at the top, a small black adapter board, a cable with a D-sub plug, an interface board and a black programmer unit with its USB light on

From module to computer

The airbag module is wired to a small black adapter board. A cable and plug carry the connections down to an interface board in the programmer's socket, and a USB cable leads from the programmer to the computer that runs the software.

On the bench the module talks to the programmer, with no car in the loop.

The module's plug
A hand holding the airbag module by its yellow connector, with thin yellow wires from the connector to a bundle of coloured wires that lead to the programmer

The plug side

On the bench there is no car and no wiring loom, so the module's connector is wired to the programmer's harness instead. Thin yellow wires run from the connector pins to a bundle of coloured wires that leads to the programmer.

The module gets everything it needs from the bench, in place of the car.

06What the screen shows

ProgrammerErase · Write
Programmer software on a computer screen: Connect shows Success, Erase DFLASH shows Success and Write DFLASH is in progress, with the processor part number R7F7016863 in the title bar

The programmer, mid-job

The software lists each stage as it runs. In this photo Connect and Erase DFLASH both show Success, and Write DFLASH is in progress. The status line at the bottom of the screen read Writing data… 56%.

The title bar shows a Renesas part number, R7F7016863, for the processor being worked on. DFLASH is the data flash, the part of the processor's memory that holds data the module needs to keep.

Fault listRead on the bench
Computer screen showing a list of airbag system faults read from the module on the bench, such as sensor initialization errors and lost communication with other modules

A long list of faults

Read on the bench, the module lists faults like these: sensors it can't see (initialization error) and other modules it can't reach (lost communication with the engine, vehicle dynamics, instrument cluster and body control modules).

That is what a module reports when it isn't plugged into a car, so a list like this on the bench is not a list of faults in the car.

07What a reset does, and what it doesn't

  • It clears the stored crash data so your original module can be used again.
  • It doesn't replace parts. Airbags and seatbelt pretensioners that have fired, and damaged sensors or wiring, still have to be replaced. Until they are, the airbag light stays on.
  • It doesn't repair the car. A car that has been in a crash needs a proper repair and inspection.
  • It isn't a way to hide an accident. Crash data can matter for insurance and disputes. Check with your insurer first, and with the manufacturer if a new module is specified.

A module that has been crushed, burnt or soaked should be replaced, not reset. We will tell you if that is what we find.

08How we handle it

  1. Send us the detailsThe make, model and year, the part number on the module label, and what the car is showing. A photo of the label helps.
  2. We check the moduleWe work out whether we can process it and which bench method suits it. Some modules can't be done, and we say so before anything is touched.
  3. Quote before workAirbag crash data reset starts from $89 for all car makes. The price for your module is confirmed before any work starts.
  4. Bench work and a checkThe crash data is cleared on the test bench and the module is checked before it goes back. It is your original module, so it keeps its own vehicle information.

We can't promise a result for a module we haven't seen, which is why we check it first.

09Is this your car?

  • Airbag light on since a crash? A module that has stored a deployment stays locked until the crash data is cleared or the module is replaced.
  • A scan tool shows airbag codes and can't clear them? The crash data is a locked record in the module. A scan tool can't erase it.
  • Told you need a new module? Ask whether the original can be reset. A replacement usually has to be matched to the vehicle.
  • Told a newer module can't be reset? Some can, with the right bench method. Send us the part number and we will say whether we can.

To get a quote, send us the make, model and year, the part number on the module label and what the car is showing. We take postal repairs Australia-wide, so contact us first and we will confirm before you send it. See also our airbag reset and module services, and the full guide, airbag module reset in Brisbane.

5% off every repair, or a 5% price beat

No competitor quote needed for the discount: every repair booked with CQ Electronics in Brisbane comes with an automatic 5% off the quoted price. And if you find a genuine lower price for the same repair elsewhere, we will beat it by 5%. The price beat can't be combined with the 5% off, so you get one or the other.

Frequently asked questions

Can airbag crash data be cleared after the airbags deploy?

Often, yes, for modules we can process. After a deployment the airbag (SRS) module stores the crash data and locks, and the airbag light stays on. We clear that data on a test bench so your original module can be used again. Not every module can be done, so we check the part number first and confirm before any work.

Why can't my scan tool clear the airbag light after a crash?

A scan tool can read the airbag fault codes, but the crash data is stored in the module's memory as a locked record, and a scan tool has no way to erase it. On newer modules the data is also encrypted. Clearing it takes bench equipment and a method that suits that module.

Why are newer airbag modules harder to reset?

Cars keep getting more electronic, and the modules inside them more complex. Many older airbag modules kept the crash record in a small separate memory chip. Newer modules, such as the one from this Subaru Outback, keep it in the processor's own memory, and the data is encrypted. No single method works on every module, so on the test bench we use different methods, depending on the module.

Can you reset the airbag module of a 2022 Subaru Outback?

This article shows one we worked on. Send us the year, the module part number from its label and what the car is showing, and we will tell you whether we can process your module. We can't promise a result for a module we haven't seen.

Do I have to buy a new airbag module after the airbags deploy?

Not always. A new module is one option, and a replacement usually has to be matched to the vehicle. The other is to have the crash data cleared from your original module, which keeps the original unit. Some manufacturers specify a new module after a deployment, so if an insurer or a dealer is involved, check what they require before you decide.

Does a crash data reset replace the airbags and sensors?

No. A reset clears the stored crash record only. Airbags that have fired, seatbelt pretensioners that have fired and damaged sensors or wiring still have to be replaced, and the car should be repaired and inspected properly. Until they are, the airbag light stays on or comes straight back.

Is clearing crash data a way to hide an accident?

No, and we don't offer it for that. Crash data can matter for an insurance claim or a dispute, so check with your insurer before the module is reset. The aim is to get the safety system working again after the car has been properly repaired.

Is the reset module still my car's original module?

Yes. Your own module goes back into your car, so it keeps its own part number and vehicle information. A replacement module usually has to be matched to the vehicle. If your vehicle needs an extra step after a reset, we will tell you before the work starts.

How much does a Subaru airbag crash data reset cost in Brisbane?

Airbag crash data reset starts from $89 for all car makes. The price for your module is confirmed before any work starts. Every repair booked with CQ Electronics includes 5% off the quoted price. If you find a genuine lower price for the same repair elsewhere, we will beat it by 5%. The price beat can't be combined with the 5% off, so you get one or the other.

Can I post the airbag module to you from outside Brisbane?

Yes, we accept postal repairs Australia-wide for eligible electronics. Contact us first with the make, model, year and the part number on the module label so we can confirm it is suitable, and pack the module so it can't be knocked around in transit.

Will you beat a cheaper quote from another Brisbane repairer?

Yes. Every repair already includes 5% off the quoted price, and if you find a genuine lower price for the same repair elsewhere, we will beat it by 5%. The price beat can't be combined with the 5% off, so you get one or the other. Tell us about the other price when you request a quote.

Airbag light on after a crash?

Send us the make, model, year and the module part number. CQ Electronics clears airbag (SRS) crash data from our workshop in Seventeen Mile Rocks, Brisbane, from $89, with 5% off every repair, or a 5% price beat on any genuine lower price (not combined).

Request a quote →

Related repair guides